ServicesWindow Replacement
Window Replacement in Whittier
We remove worn-out windows, set new dual-pane units square and sealed, and clean as we go. Floors get covered, debris leaves with us each day, and you get a clear answer on whether an insert or a full-frame install fits your home.

When replacing a window is the right call
A window is worth replacing when the problem is in the unit itself, not just a part. Fog between dual panes means the edge seal has failed and the argon is gone. Aluminum frames that sweat in winter and burn to the touch in August conduct heat straight through. Sashes that bind or will not lock usually point to warped frames or worn tracks that no adjustment will fix.
Most of the homes we see in Whittier and towns like La Habra and Norwalk still have some original aluminum sliders or early dual-pane units from the 1980s and 1990s. We replace them with vinyl frames, Low-E coated glass and insulated spacers, sized to the opening so the sash slides freely and the weatherstripping actually seals.
How we work matters as much as the product. Every opening gets drop cloths inside and out, furniture near the wall is moved or wrapped, and we vacuum the sills and sweep the walkway before we leave each day.
What our window replacement covers
- Measuring each opening
- We measure width and height at three points and check for square, because stucco openings in older homes are rarely true. Those numbers decide the unit size and which install method suits the opening.
- Choosing the install method
- With a retrofit insert, the existing frame stays put and the new unit is set into it, so your stucco and interior trim are not disturbed. When the old frame is damaged, or you want more daylight, we remove everything down to the rough opening instead. You hear the pros and cons for your walls during the visit, and our Window Retrofitting page covers inserts in more detail.
- Removal and haul-away
- Old sashes, frames and glass come out carefully and go straight to our truck. Nothing is left stacked in the side yard overnight.
- Sealing and flashing
- Each unit is shimmed level, fastened, and sealed with exterior-grade sealant at the stucco line. On full-frame jobs we flash the opening so water sheds out instead of into the wall.
- Interior finish and cleanup
- We fill the interior gap with low-expansion foam, set trim where it is needed, remove labels and wipe the glass. Then we vacuum the sill, the floor below it and any dust that drifted.
Signs your windows are due for replacement
Fog or haze between panes
Moisture trapped inside a dual-pane unit means the seal has failed. The insulating gas has leaked out, and cleaning cannot reach it.
Condensation on aluminum frames
Bare aluminum conducts cold, so water beads on the frame on cool mornings and runs onto the sill. Over time that stains paint and swells wood trim.
Sashes that stick or drop
Worn rollers, bent tracks or a twisted frame make sliders drag and single-hungs slam shut. If the frame itself is out of shape, new hardware will not hold.
Rooms that track the weather
A bedroom that bakes in the afternoon or a living room you cannot keep warm often traces back to single-pane glass. Our Energy Efficient Windows page explains how Low-E coatings cut that heat gain.
Drafts and street noise
Dried-out weatherstripping and gaps around the frame let air and sound in. A new unit sealed into the opening closes both.
How a replacement day runs
- 1
Free in-home estimate
We look at every window, measure, and talk through frame materials and glass options. You get a written estimate with no sales pressure and no obligation to move forward.
- 2
Ordering and permit
Your windows are built to the measured sizes. If your project needs a building permit, we handle the application and inspection scheduling, and the glass we specify meets California energy code.
- 3
Protecting the house
On install day we lay drop cloths at each opening, cover nearby furniture with plastic and set a mat at the door we use. If the home predates 1978, we mist and contain old paint so dust stays on the sheeting.
- 4
Removal and install, one opening at a time
We take out one window, set and seal the new one, and move on, so your home is never left open. Most houses with a handful of windows are finished in a day.
- 5
Walk-through and final cleanup
We open, close and lock every window with you, then vacuum, bag the sheeting and haul away every scrap of the old units.

What moves the cost of window replacement
Your price depends on the openings in your home and the work each one needs. The estimate lists every window as its own line, with the unit, the install method and any extra labor shown, so you can see where each part of the total comes from. Nothing is added after the fact without a conversation first.
- Number and size of windows
- More openings spread setup time across the job. Oversized picture windows and large sliders need heavier glass and sometimes a second installer.
- Insert versus full-frame
- Inserts go faster because the old frame stays in place. Full-frame work adds stucco cutting, flashing and patching around the new unit.
- Glass package
- Low-E coatings, argon fill, tempered glass near doors and tubs, and obscure glass for bathrooms each change the unit price.
- Frame condition and access
- Rotted wood subframes, second-story openings and windows behind dense landscaping take more labor to reach and repair.
Window replacement questions
Something not covered here? (562) 554-5955
Will you have to cut my stucco?
Not with an insert install. The new window fits inside the existing frame, so the stucco and drywall stay intact. Full-frame installs do require cutting back the stucco, and we patch and texture that strip afterward.
How much mess should I expect inside?
Very little reaches the room. We cover the floor and nearby furniture, cut and trim outside where we can, and vacuum each sill before moving on. At the end of the day the only change you should notice is the new window.
Does an adult have to stay at the house all day?
We ask for an adult when the crew arrives, so we can walk through the openings together and agree on which door and path we will use. We also want you back for the final check, when we test each sash and lock with you. The hours in between are yours, so you can work from a room we are not in or run errands.
Is it okay to do the worst windows first and finish the house later?
That works fine. On the first round we record the frame color, grid pattern and sightlines, so the windows we add in a later phase match the ones already in. Plenty of people start with the bedrooms or the sunniest wall and spread the cost over time.
What frame material do you recommend?
For most homes here, vinyl is the practical choice. It does not conduct heat like aluminum, it holds up to strong sun, and it needs no painting. We will show you samples at the estimate.

See what new windows would take
We will measure every opening, explain insert versus full-frame for your walls, and give you a written estimate before you decide. We serve Whittier and the surrounding area, including South Whittier and Pico Rivera.