Skip to content

Free in-home estimate, drop cloths down first

(562) 554-5955
(562) 554-5955

ServicesSliding Door Replacement

Sliding Door Replacement in Whittier

We swap out worn sliding glass doors for new units that roll smoothly, latch firmly and hold back summer heat. Drop cloths protect your floors through the install, we haul the old door away, and the room gets vacuumed and wiped before we pack up.

Over-the-shoulder view of an installer in gloves positioning a white-framed sliding glass door panel at a stucco house opening, with drop cloths and a fenced backyard

When a new sliding door is the right call

No opening in your home gets used as hard as the slider. The panel moves back and forth many times a day, grit settles in the bottom track, and the small rollers it rides on slowly wear flat. When the frame itself is bent, corroded or out of square, new rollers and a track insert only buy a little time.

Many homes around Whittier still have the original aluminum sliders with single-pane glass and no thermal break. The metal frame conducts summer heat straight into the room, and the felt weatherstrip has usually shrunk to nothing. Replacing the whole unit fixes the drag, the drafts and the heat gain in one visit.

We measure the opening, look at the sill and the wall around it, and tell you plainly what the new door will involve before you decide anything.

What the replacement covers

Removal of the old unit

We lift out the panels, cut the old frame free and carry everything out to our truck. Nothing is left on your lawn or in your garage.

Sill pan and flashing

Water that gets under a door sill rots the subfloor slowly and quietly. A sloped pan goes under the new sill, and the flashing is layered shingle-style over it, so any water that gets in runs back out rather than soaking the slab edge or framing.

New frame, set plumb and level

The frame is shimmed at the jambs and head so the panel meets the interlock evenly from top to bottom. A frame that is off by even a little makes the lock hard to engage and lets air slip past the seal.

Tempered, insulated glass

Code requires safety glass in doors, so every panel is tempered. We offer dual-pane units with low-E coatings that cut solar heat gain, which you can read more about on our Energy Efficient Windows page.

Roller and lock adjustment

Before we leave, we adjust the rollers so the panel glides with one hand and test the latch, the interlock and the screen.

Floor protection and cleanup

Drop cloths go down from the door to the work area, and the interior side is vacuumed and wiped when the door is in. Caulk lines are tooled clean, inside and out.

Signs your sliding door is due for replacement

  • It drags or jumps the track

    Flattened rollers and a worn aluminum track make the panel grind. If adjustment no longer helps, the frame may be out of square.

  • Fog between the panes

    A failed seal on a dual-pane door lets moist air in, and the haze cannot be wiped away. The insulating gas is already gone at that point.

  • Drafts at the interlock

    If you feel air where the two panels meet, the weatherstrip has shrunk or the panels no longer line up.

  • Hot glass in the afternoon

    Single-pane glass in a west- or south-facing opening can turn a family room into an oven. New low-E glass blocks much of that heat.

  • The lock will not catch

    A latch that only engages when you lift or shove the panel is a security problem, usually caused by a sagging frame.

How the work goes on install day

  1. 1

    Measure and order

    At the free in-home estimate we measure the rough opening in several places, check whether the frame can come out cleanly, and go over glass and frame options. Your door is then built to those measurements.

  2. 2

    Protect the room

    On install day we clear a path, lay drop cloths and cover nearby furniture. Outside, we put down tarps on patios or planters below the opening.

  3. 3

    Remove and prepare

    The old door comes out, and we scrape the opening, check the framing and set the sill pan. If we find damaged wood, we show you before going further.

  4. 4

    Install and seal

    The new frame is set, shimmed, fastened and flashed, then the panels and screen go in. We seal the exterior and finish the interior trim.

  5. 5

    Test and clean up

    We run the panel, adjust the rollers, check the lock, then vacuum, wipe the glass and haul away every scrap. Most single-door jobs finish in one day.

What moves the cost of a sliding door

Every opening has its own size, framing and condition, so we price each door only after we have seen it. You can get your quote by phone or at the in-home visit, itemized so each part of the job has its own line. If pulling the old unit uncovers a problem nobody could see beforehand, such as soft sill framing, we pause, walk you over to look at it and agree on the fix with you before any added work begins.

Size and panel count
A standard two-panel door costs less than a wide three- or four-panel unit, which needs heavier frame sections and more glass.
Retrofit or full frame
A retrofit fits inside the old frame and avoids cutting stucco. Full removal costs more but lets us flash the opening properly and correct any damage hidden behind the old frame.
Frame material and glass
Vinyl, fiberglass and thermally broken aluminum each price differently, and low-E coatings or laminated glass add to the cost of each panel.
Condition of the opening
Rotted sill framing or a cracked slab edge has to be corrected before the new door can sit level, and we note it on your written estimate before touching it.

Sliding door questions we hear often

Something not covered here? (562) 554-5955

Will you have to cut into my stucco?

Not always. If the old frame is sound and square, a retrofit unit can mount inside it with no stucco work. If the frame is damaged or leaking, full removal is the better choice, and we patch the stucco around the new frame.

How long will my home be open to the outside?

Usually only a few hours. The existing door stays in place until the replacement has been delivered and inspected for damage or wrong sizing, and we close the opening the same day.

Can I change from two panels to three, or make the opening wider?

A different panel layout in the same opening is often possible. Widening the opening means changing the header over it, which is structural work, so we look at it during the estimate and explain what it involves. For very wide openings, our Multi-Folding Doors page may be worth a look.

What happens to my old door?

We haul it off. Panels, frame and track go on our truck, and we sweep the ground outside the opening as well as the floor inside.

Do my floors need anything special?

Nothing beyond moving small items away from the door. Tile, wood and carpet all get covered from the opening to our work area, and we clean them once the door is in.

Single-story stucco house with new white-framed windows on each side of a black entry door with glass sidelites, shrubs, lawn, walkway, and a tool bin and bucket

Ready for a door that slides with one finger?

We will measure your opening, show you the frame and glass choices, and give you a clear price with no sales pressure or obligation. Your floors stay covered and the old door leaves with us.